A lesson in electricity

Hi all,

Has been a long time between posting on this blog. I have been doing odds and ends as usual, which is how life goes. Models come and go as I do odd jobs for some friends (I've probably weathered close to 70 wagons in the last month) so you could say I've learnt a bit about that haha.

Anyway, today's topic is about electricity, namely learning about the application of resistors with DCC, and lights.

I recently fitted a Tsunami 2 Steam 2 to my Eureka Garratt, as a replacement for the aged QSJ decoder of 14 years in the locomotive. The installation was easy, and following the instructions allowed me to get a locomotive running within about an hour, with a keep alive well. I had followed the recommendation of adding 1/4 watt, 580k resistors to the headlight anodes to allow the LED's to work in the loco. I over compensated and used 1/2 watt 580k resistors instead.

The lights didn't work, and I was puzzled.

I recently purchased a DJH 38 with a sound decoder, which I didn't like so I proceeded to install a Tsunami 2 1100 and a Soundtraxx KA. I wired up the headlight previously fitted with a 1/2 watt 580k resistor, removing the original one. Reassembled and tested, but the headlight wasn't working even though it did before. I scratched my head and wondered, am I using the correct resistor?

Turned out I wasn't. I reinstalled the original resistor this morning, and the headlight lit up like a Christmas tree.

Here is the subject of my learning curve today:

Subsequently, I will have to pay more attention when I fit lights to locos...

More updates of normality will recommence soon...

Cheers!

Black oiling locomotives

Hi all,

Just a quick post today. I had in my mind a way to get a black oiled appearance on a steam locomotive which involved using Tamiya Line Accent. This is was something I wanted to try for some time before actually doing it properly today.

What is black oiling?

Black steam locomotives were often 'spruced' up with a layer of black oil to give the locomotive a glossy finish. This was something commonly done with locomotives used for enthusiast specials or even by some depots as a regular occurrence in the steam era.

Straight panel line is poured into an airbrush and sprayed at around 25psi. When spraying, ensure you're not spraying too much product otherwise you can get runs. A light spray just to give a basic emphasis over the paint to darken it ever so slightly as black oil was used for. You can build up coats just to get the final finish.

Here are some photos of the finished loco.

Cheers

Painting the AC state car

Hi all,

I recently commenced building a Lloyds AC state car. Easily, one of the nicest kits I have come across. It's a theme with the old milky bar kits how simple and well thought out they are.

The kit went together fairly straightforward, with no major hiccups. The end handrails and etching for the end platform are a bit of a prick, but that's a given with the nature of the kit.

The carriage was dismantled to be painted, with the body and underframe being primed separately. I use Tamiya fine surface primer, a very forgiving primer to use I've found.

Once everything was primed, the underframe was hit with XF1 flat black from Tamiya. I'll have to redo it a bit later, but it's not an issue right now.

I picked up some Tamiya XF9 Hull Red and XF55 Deck Tan to paint the car. The whole carriage was painted in the Hull Red, and then left to dry. A mixture of 10mm, 3mm, 1mm and 0.7mm masking tape was used to mask off to paint the cream. What a prick of a job.

Anyway, here is where we are at now. I plan to fit some Casula 2AA bogies and lower it a little, but not today. I do plan to add the rest of the lining at a later date...

Cheers

ALCo's of all sorts

Hi all,

Just a quick few images of some recently weathered 48's and a 45. 4833 is a renumber job as is 4821. 4833 is an Auscision 48 fitted with a Tsunami 2 with a sugar cube speaker in the rear, and 4821 is a Powerline with a Tsunami 2 Atherns board mounted with a sugar cube. 4821 still needs some numberboard decals and is almost there.

4512 is an Auscision 45, with a Tsunami 2 and a decent coat of grime.

Also included is an image of my ever growing export grain train. It'll be around 35 wagons long when complete.

Enjoy.

Cheers

4833 is a renumbered Auscision Mk1 48. Representing a clean but used 48, it also doubles up as a preserved loco. Just very subtle weathering to tone it down a touch. Infront Models kindly provided me with the nose numbers and Ozzy decals were used for cab numbers. 

4821, a renumbered Powerline 48. Ozzy decals on the side with a liberal coat of grime to the body.  I need to add nose numbers yet but that's low on the priority list. 

4512 is a 45 sold to me as a dummy however it had a motor and all the electronics in it. Score! Weathered it up and have ran it ever since, it's one of my favourite locos. 

ALCo triples. Will be seen very often on my export grain. 

42203, 4833 and 42101 slowly ease their loaded grain train through Maitland. A place where 422's and 421's were rarely ever seen, however this is modelling. 

Austrains FS cars, the roofs.

Hi all,

I share quite a lot of my modelling work onto a facebook group which one of the members recently asked me, how do I do Malthoid roofing on FS carriages, in particular the Austrains ones.

I decided to dedicate a blog post to not just that, but some other improvements that can be made to the carriages for running reliability etc.

The Austrains FS cars were a welcomed addition into the RTR rollingstock availavle for HO scale modellers when they hit the market. The carriages were of a different assembly and detail standard to the common Trax/Powerline cars. Separately applied roof vents, handrails, interiors, detailed underframes and some other refinements made them well received. However, unlike the Powerline carriages they do not have removable roofs. This presents an issue when detailing the roofs of these cars as it makes it a little bit trickier to do the roofs neatly.

Anyway, let's get into it.
We will need
Tamiya 10mm masking tape
Steel ruler
Lead pencil
Exacto knife
Cutting pliers
Appropriate paint for the roof (I use Testors silver spray paint)
And more masking tape.

I begin by removing the roof vents. I use some cutters to remove them, just to lever them out of the roof as shown in the photo below.

Firstly, I measure 7.5mm in from each end of the car body. I will mark where that 7.5mm is on each end of the roof, and from that mark is where I commence laying my masking tape.

The Austrains cars are 22.5cm long roofs. The 7.5mm leaves 15mm out of the roof, leaving 21cm to play with. I would also suggest that you can measure to the centre of the roof, find it and add 5mm either side. It'll give you a similar result to what we do here.

From here it is as simple as taking strips that will fit across the roof and laying them down. You don't have to overlap them, and they should sit together with very little gap between them. Lay them across til you have a complete roof covered.

Once the roof is covered you can begin to cut the strips back flush with the gutters on the roofs to give it a clean look. I very carefully hold the ruler up against the gutter and gradually score the masking tape to give a clean cut edge. This is done on both sides.

Once that is complete, I refit the roof vents. To clear the holes out, a quick jab through the hole with a sharp blade will make clear room for the vent to reseat where required.

To finish up, I take some more 10mm tape and mask on the car body hard up against the roof line. That prevents overspray from creeping under and ruining the paint. I then will mask the ends of the cars to leave the navy sealed ends the 'right' colour and mask the rest of the body with 40mm masking tape to prevent overspray.

Hit it with silver paint, remove your masking and that's that.

This car has had AR kits 2BS bogies fitted and some light weathering added. I would like to fade to candy red a little bit but that's for a future post.

Take care all,

Cheers.